Audio Fix / setup help
Topping E70 Velvet: select a different already-connected input
Topping E70 Velvet — select a different already-connected input. Use the stated exact hardware and connection scope.
Manufacturer-documented Reviewed 2026-11-09 · Revision 1
Follow these checks in Audio Fix →When this guide applies
Exact Topping E70 Velvet. The current source is actively connected and has played correctly. A second intended source is also already connected correctly. For Bluetooth it is already paired and connected; this guide does not establish a new pairing. You want to hear the destination source through the existing output.
Connection scope: USB audio · Optical digital audio · Bluetooth. Symptom: Switching between devices isn’t working.
This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.
If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.
Checks and possible outcomes
Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.
scope
Confirm the model and connection
The current source is actively connected and has played correctly. A second intended source is also already connected correctly. For Bluetooth it is already paired and connected; this guide does not establish a new pairing. You want to hear the destination source through the existing output.
Look for: Confirm this exact setup and observation before continuing.
- If Yes, I confirm → Accept a source interruption and possible remembered level?
- If No / my setup differs → Continue with source and model support
- If I cannot confirm → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
switch-consent
Accept a source interruption and possible remembered level?
Changing input interrupts media and some settings remember earlier levels. Continue only outside calls/recordings, with agreement to pause sources, lower volume and mute downstream amplification before selecting another input.
Look for: Explicit informed acceptance is required before the next action.
- If I accept these effects → Pause media
- If No / leave this unchanged → Continue with source and model support
- If I cannot confirm → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
a1
Pause media
Pause both the existing and destination source before changing the input.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Lower all active levels
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
a2
Lower all active levels
Reduce the unit volume and keep downstream amplifier/speaker controls muted. Do not select a fixed DAC/line mode.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Select the intended input
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
a3
Select the intended input
Use the remote previous/next input buttons until the display shows the already-connected USB, optical or Bluetooth source you intend to hear. Do not change output mode.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Compare quiet media
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
a4
Compare quiet media
Verify the destination source indication, then resume familiar media and approach a comfortable level cautiously.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Check the result
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
observe
Check the result
Does the displayed input match the intended source and does its quiet media reach the existing output?
Look for: Confirm this exact setup and observation before continuing.
- If Yes, I confirm → Checks completed
- If No / my setup differs → Continue with source and model support
- If I cannot confirm → More information is required
- Manufacturer-documented Topping E70 Velvet — official official manual ↗English page 2: operation, remote, channel balance, brightness, auto standby — E70 VELVET is a line-output DAC with USB/optical/BT inputs and RCA/XLR outputs, not a headphone amplifier. Remote output selects RCA/XLR/both; known mute can be released with MUTE. Balance 0.0 is centred; brightness LA dims after 30 seconds; input-signal auto standby is A-1. Holding brightness 3 seconds with BT active enters pairing.Exact Topping E70 Velvet. · Source checked 2026-11-09
Possible result
More information is required
An unknown state is not a diagnosis. Record the last visible indication and consult the exact model instructions.
insufficient data
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Continue with source and model support
Keep the source, connection and last observation. Do not reset, open equipment or change full-scale output to compensate for an unconfirmed result.
next support
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Checks completed
The requested observation was confirmed in this setup. It does not establish a hardware repair or guarantee another source behaves the same.
steps completed
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.