Audio Fix / setup help

Pro-Ject T1 EVO BT: switch the BT transmitter to an intended receiver

Pro-Ject T1 EVO BT — switch the BT transmitter to an intended receiver. Follow the exact documented route and keep the actual result.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Pro-Ject T1 EVO BT. Exact T1 EVO BT only. A receiver change may interrupt the current wireless output; this is not multipoint. Only normal external user controls; no mains modification, chassis opening, reset or firmware installation.

Connection scope: Bluetooth. Symptom: Switching between devices isn’t working.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

You are deliberately changing the Bluetooth receiving speaker/headphones, know its pairing procedure, all owners accept interrupting the old receiver and both playback levels are safe.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — T1 EVO BT specific information — BT pairing — The BT-output transmitter pairs automatically with a Bluetooth receiver. Consult the receiver manual. Only when changing receiver, restart the BT module with its switch OFF then ON. This is not phone-to-turntable Bluetooth input.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a1

Put only the intended new receiver in its documented pairing mode

Use that receiver’s own instructions. Do not assume a phone can receive turntable audio.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — T1 EVO BT specific information — BT pairing — The BT-output transmitter pairs automatically with a Bluetooth receiver. Consult the receiver manual. Only when changing receiver, restart the BT module with its switch OFF then ON. This is not phone-to-turntable Bluetooth input.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a2

Switch the T1 EVO BT module OFF

Use the identified BT module switch, not a factory-reset command.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — T1 EVO BT specific information — BT pairing — The BT-output transmitter pairs automatically with a Bluetooth receiver. Consult the receiver manual. Only when changing receiver, restart the BT module with its switch OFF then ON. This is not phone-to-turntable Bluetooth input.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a3

Switch that BT module ON

Allow automatic pairing to the intended ready receiver; do not infer successful audio from mere proximity.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — T1 EVO BT specific information — BT pairing — The BT-output transmitter pairs automatically with a Bluetooth receiver. Consult the receiver manual. Only when changing receiver, restart the BT module with its switch OFF then ON. This is not phone-to-turntable Bluetooth input.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

result

Check the actual result

Does the intended receiver confirm connection and play at a safe level?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — T1 EVO BT specific information — BT pairing — The BT-output transmitter pairs automatically with a Bluetooth receiver. Consult the receiver manual. Only when changing receiver, restart the BT module with its switch OFF then ON. This is not phone-to-turntable Bluetooth input.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

Possible result

Confirm the unknown detail first

Do not infer a source setting, installed cartridge, connector role, software state or partner capability. Obtain the exact documentation before continuing.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, input and last observed response. These checks do not diagnose a failed component. No reset, service work or blind update is prescribed.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — keep the observed result

      This records the observation in this particular setup, not a guaranteed cure, physical Audio Review test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top