Audio Fix / setup help

Pro-Ject T1 EVO BT: verify the selected LINE or PHONO output path

Pro-Ject T1 EVO BT — verify the selected LINE or PHONO output path. Follow the exact documented route and keep the actual result.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Pro-Ject T1 EVO BT. Existing connected system; inspect with units off, no live cable changes or extreme volume compensation. Only normal external user controls; no mains modification, chassis opening, reset or firmware installation.

Connection scope: Analog line / headphone audio · Turntable / phono audio. Symptom: Sound goes to the wrong output.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

The actual cartridge and receiving amplifier input are documented. The system is off and accessible socket labels can be inspected without disturbing the stylus.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — Connection to amplifier — The output can be selected as PHONO for a suitable phono preamp, or LINE for an amplifier’s AUX/CD/line input. The physical output setting must match the receiving input; the integrated stage is not a passive-speaker amplifier.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a1

Identify the actual receiving input

Read whether it is a line input or an appropriate phono-stage input. Stop if an external phono stage’s position is uncertain.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — Connection to amplifier — The output can be selected as PHONO for a suitable phono preamp, or LINE for an amplifier’s AUX/CD/line input. The physical output setting must match the receiving input; the integrated stage is not a passive-speaker amplifier.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a2

Match the actual output selector to that route

With the system still off, confirm LINE only for a line input, or PHONO only for the documented matching phono preamp. Stop if the existing cable route is incompatible.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — Connection to amplifier — The output can be selected as PHONO for a suitable phono preamp, or LINE for an amplifier’s AUX/CD/line input. The physical output setting must match the receiving input; the integrated stage is not a passive-speaker amplifier.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

a3

Observe only through the confirmed compatible route

Restart normally at low amplifier level. If compatibility was not confirmed, stop before playback and plan a correct connection with the dealer.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — Connection to amplifier — The output can be selected as PHONO for a suitable phono preamp, or LINE for an amplifier’s AUX/CD/line input. The physical output setting must match the receiving input; the integrated stage is not a passive-speaker amplifier.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

result

Check the actual result

Is the existing signal topology compatible and playback sensible?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Pro-Ject T1 EVO BT official user guide ↗pp.5–9 — Connection to amplifier — The output can be selected as PHONO for a suitable phono preamp, or LINE for an amplifier’s AUX/CD/line input. The physical output setting must match the receiving input; the integrated stage is not a passive-speaker amplifier.Exact Pro-Ject T1 EVO BT. Cartridge, counterweight and belt variant must be known. No original non-B or non-EVO controller is substituted. · Source checked 2026-11-09

Possible result

Confirm the unknown detail first

Do not infer a source setting, installed cartridge, connector role, software state or partner capability. Obtain the exact documentation before continuing.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, input and last observed response. These checks do not diagnose a failed component. No reset, service work or blind update is prescribed.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — keep the observed result

      This records the observation in this particular setup, not a guaranteed cure, physical Audio Review test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top