Audio Fix / setup help

Eversolo DMP-A10: pair a first Bluetooth music input

Eversolo DMP-A10 — pair a first Bluetooth music input. Follow the exact documented route and keep the actual result.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Eversolo DMP-A10. First source enrollment only, not the separate handheld remote pairing. Only normal external user controls; no mains modification, chassis opening, reset or firmware installation.

Connection scope: Bluetooth. Symptom: My devices won’t pair or reconnect.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

This is the exact model and first phone/source enrollment, its Bluetooth antenna is already correctly fitted where required, no update is in progress and listeners accept selecting Bluetooth input.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Eversolo DMP-A10 official User Manual v1.0 ↗PDF pages 30: Bluetooth Input — Use Settings > Source > Bluetooth In, then enable source Bluetooth and pair the displayed DMP-A10 receiver. Receiver supports SBC/AAC. Actual codec depends on the transmitting source; no codec or developer-setting change is prescribed.Exact Eversolo DMP-A10 original model, not Master/Gen2. Visible menu must match this documented route; newer firmware is not assumed equivalent. · Source checked 2026-11-09

a1

Select Settings > Source > Bluetooth In

Use the source input, not a remote-control pairing dialog.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Eversolo DMP-A10 official User Manual v1.0 ↗PDF pages 30: Bluetooth Input — Use Settings > Source > Bluetooth In, then enable source Bluetooth and pair the displayed DMP-A10 receiver. Receiver supports SBC/AAC. Actual codec depends on the transmitting source; no codec or developer-setting change is prescribed.Exact Eversolo DMP-A10 original model, not Master/Gen2. Visible menu must match this documented route; newer firmware is not assumed equivalent. · Source checked 2026-11-09

a2

Open the intended source’s Bluetooth available-device list

Keep it nearby and do not forget existing unrelated devices.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Eversolo DMP-A10 official User Manual v1.0 ↗PDF pages 30: Bluetooth Input — Use Settings > Source > Bluetooth In, then enable source Bluetooth and pair the displayed DMP-A10 receiver. Receiver supports SBC/AAC. Actual codec depends on the transmitting source; no codec or developer-setting change is prescribed.Exact Eversolo DMP-A10 original model, not Master/Gen2. Visible menu must match this documented route; newer firmware is not assumed equivalent. · Source checked 2026-11-09

a3

Select the actual DMP-A10 receiver

Confirm its identity and compare a quiet music selection.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Eversolo DMP-A10 official User Manual v1.0 ↗PDF pages 30: Bluetooth Input — Use Settings > Source > Bluetooth In, then enable source Bluetooth and pair the displayed DMP-A10 receiver. Receiver supports SBC/AAC. Actual codec depends on the transmitting source; no codec or developer-setting change is prescribed.Exact Eversolo DMP-A10 original model, not Master/Gen2. Visible menu must match this documented route; newer firmware is not assumed equivalent. · Source checked 2026-11-09

result

Check the actual result

Does the intended Bluetooth source connect and play?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Eversolo DMP-A10 official User Manual v1.0 ↗PDF pages 30: Bluetooth Input — Use Settings > Source > Bluetooth In, then enable source Bluetooth and pair the displayed DMP-A10 receiver. Receiver supports SBC/AAC. Actual codec depends on the transmitting source; no codec or developer-setting change is prescribed.Exact Eversolo DMP-A10 original model, not Master/Gen2. Visible menu must match this documented route; newer firmware is not assumed equivalent. · Source checked 2026-11-09

Possible result

Confirm the unknown detail first

Do not infer a source setting, installed cartridge, connector role, software state or partner capability. Obtain the exact documentation before continuing.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, input and last observed response. These checks do not diagnose a failed component. No reset, service work or blind update is prescribed.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — keep the observed result

      This records the observation in this particular setup, not a guaranteed cure, physical Audio Review test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top