Audio Fix / setup help

Dual CS 529, Audio-Technica AT-LP70XBT and AT-LP60XBT: Check automatic start or arm return

Dual CS 529, Audio-Technica AT-LP70XBT and AT-LP60XBT: Start a supported record automatically. Shared exact-model procedure, with model-specific prerequisites retained.

Manufacturer-documented Reviewed 2026-11-09 · Revision 2

Follow these checks in Audio Fix →

When this guide applies

Only listed exact decks, already assembled, quiet playback route, intact automatic arm. Start branch requires guard safely removed, arm restraint released, known correct speed and supported record size. Dual automatic mode17/30 cm only, not25 cm; AT labels7/12inch. Stop branch requires a rotating record and a clear arm path. No forced arm or platter movement.

Connection scope: Turntable / phono audio · Bluetooth · Analog line / headphone audio. Symptom: Buttons, touch controls or wear detection aren’t working.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the actual deck and safe setup

Is this selected exact assembled deck already normally powered, at a safe low level, with an intact automatic arm and known normal controls?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

operation

Choose the actual operation

Are you checking automatic START? Choose Yes for Start; choose No only when you intend automatic STOP/arm return from a currently rotating record.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

start-ready

Confirm start prerequisites

Are guard safely removed, arm restraint already released, correct speed selected and record size supported: Dual 17/30 cm, or AT 7/12inch?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

size

Set the actual supported record size

While stopped, choose the record’s actual size using the selected deck labels: Dual 17/30 cm or AT 7/12inch. Never infer size from speed.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

start

Begin automatic playback

Press START once on the listed AT decks, or START-STOP once on Dual CS 529. Keep hands clear and do not restrain the automatic arm.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

start-result

Observe automatic start

Does the arm reach the intended supported record start normally?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

stop-ready

Confirm a safe automatic-return check

Is the platter currently rotating, listening level already low and automatic arm path unobstructed, with no damaged stylus or jam?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

stop

Request automatic arm return

Press STOP once on the listed AT decks, or START-STOP once on Dual CS 529. Do not touch the arm during its automatic return.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

wait-return

Wait for automatic return to finish

Wait until the arm reaches its rest and the platter stops. Do not remove a rotating record or touch the moving arm; stop for support if it jams.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

stop-result

Observe platter and arm

Have platter rotation stopped and the arm returned to its rest? Do not remove a still-rotating record.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dual CS 529 official Owner’s Manual V1 DE/EN ↗English PDF pages 21: Operating the turntable — The speed selector sets33/45/78with an LED. Automatic play needs the correct17/30 cm record-size lever and released rest fastener. No automatic function for25 cm(10inch) records. START/STOP begins/ends automatic play; green Start LED flashes during movement.Exact Dual CS 529; not CS429/329. Supplied Ortofon 2M Red is not assumed if the cartridge was changed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official operating instructions ↗Automatic operation, PDF pp18–19 — With record size/speed selected while stopped and the actual playback route ready, START initiates automatic arm movement. Do not alter record-size selection during playback or interfere with automatic arm motion.Exact Audio-Technica AT-LP70XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official operating instructions ↗Playing a record / Automatic operation, PDF p9 — After size and speed selection, START initiates automatic playback. Do not bump the product or change size selection during playback.Exact Audio-Technica AT-LP60XBT with actual installed cartridge already adjusted; no force inferred from another regional cartridge. · Source checked 2026-11-09
  • Manufacturer-documented Dual CS 529 Operating Manual ↗English Operating the turntable, PDF p21; controls p18 — CS 529 START-STOP begins automatic play and stops it with automatic arm return. Its automatic mode does not support25 cm records; use the actual17/30 cm lever labels.Exact CS 529; not its BLE remote-discovery workflow. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP70XBT official user manual ↗pp.14–31,40–45 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP70XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09
  • Manufacturer-documented Audio-Technica AT-LP60XBT official user manual ↗pp.6–10,12–13 — Stopping the record — STOP returns the automatic tonearm to its rest and stops the platter. Do not interfere with its movement. Some records may not trigger the automatic end return; use STOP rather than forcing the arm.Exact AT-LP60XBT, not its non-X, USB/Bluetooth, LP70X non-BT or other controller variant. Installed cartridge and receiver capabilities must be confirmed. · Source checked 2026-11-09

Possible result

Confirm the unknown detail before proceeding

Stop rather than infer an installed cartridge, partner, source level, cable capability, software version or control state.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, connection, control state and response. These checks do not diagnose a failed component or prescribe a reset, update, internal repair or mains change.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Keep the observed result

      This is the outcome observed in this setup, not a guaranteed cure, Audio Review physical test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top