Audio Fix / setup help

Audiolab 6000A MkII: Reconnect after selecting another amplifier input

Audiolab 6000A MkII — Reconnect after selecting another amplifier input. Follow the exact documented route and keep the actual result.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Audiolab 6000A MkII. The last paired source is known and available; this does not promise simultaneous multipoint. Only normal external user controls; no mains modification, chassis opening, reset or firmware installation.

Connection scope: Bluetooth. Symptom: Switching between devices isn’t working.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

Did Bluetooth disconnect after another amplifier input was selected, and is the last paired source still available?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Audiolab 6000A MKII Owner’s Manual — International ↗Connections, PDF p7 — Select BT; pair to Audiolab 6000A MKII BT. Choosing another amplifier input disconnects the source after 60 seconds; selecting BT reconnects the last paired source when available.Exact 6000A MKII international hardware/manual; not original 6000A or North American version. · Source checked 2026-11-09

a1

Return the amplifier to BT

Select BT on the amplifier.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Audiolab 6000A MKII Owner’s Manual — International ↗Connections, PDF p7 — Select BT; pair to Audiolab 6000A MKII BT. Choosing another amplifier input disconnects the source after 60 seconds; selecting BT reconnects the last paired source when available.Exact 6000A MKII international hardware/manual; not original 6000A or North American version. · Source checked 2026-11-09

a2

Check the last source connection

On the last paired source, inspect its Bluetooth connection. If automatic reconnection has not occurred, select the existing 6000A MKII entry there. Do not delete it.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Audiolab 6000A MKII Owner’s Manual — International ↗Connections, PDF p7 — Select BT; pair to Audiolab 6000A MKII BT. Choosing another amplifier input disconnects the source after 60 seconds; selecting BT reconnects the last paired source when available.Exact 6000A MKII international hardware/manual; not original 6000A or North American version. · Source checked 2026-11-09

result

Check the actual result

Does that previously paired source now show a connection?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Audiolab 6000A MKII Owner’s Manual — International ↗Connections, PDF p7 — Select BT; pair to Audiolab 6000A MKII BT. Choosing another amplifier input disconnects the source after 60 seconds; selecting BT reconnects the last paired source when available.Exact 6000A MKII international hardware/manual; not original 6000A or North American version. · Source checked 2026-11-09

Possible result

Confirm the unknown detail first

Do not infer a source setting, installed cartridge, connector role, software state or partner capability. Obtain the exact documentation before continuing.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, input and last observed response. These checks do not diagnose a failed component. No reset, service work or blind update is prescribed.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — keep the observed result

      This records the observation in this particular setup, not a guaranteed cure, physical Audio Review test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top