Audio Fix / setup help
Audient iD14 MKII: check why rear microphone input1 is replaced by the front jack
Audient iD14 MKII: check why rear microphone input1 is replaced by the front jack. Check prerequisites and the actual response before reporting an outcome.
Manufacturer-documented Reviewed 2026-11-09 · Revision 1
Follow these checks in Audio Fix →When this guide applies
Rear input1 microphone expected, but front JFET instrument cable is connected.
Connection scope: Analog line / headphone audio. Symptom: My microphone isn’t working.
This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.
If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.
Checks and possible outcomes
Start at step-0. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.
step-0
Is the missing microphone on rear input1 with a cable in the front instrument jack?
Front instrument overrides channel1; input2 has a separate path.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Can recording stop with monitor levels muted and no power/cable changes elsewhere?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII Hardware and Connections | Audient Documentation ↗Hardware and Connections — Front JFET instrument input overrides rear mic/line input1. Each microphone input has independent phantom power, enabled only after checking the microphone documentation. Four line outputs and dual headphone sockets have distinct routing; both headphone sockets share the same signal.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-1
Can recording stop with monitor levels muted and no power/cable changes elsewhere?
Removing an instrument cable can create a transient. Do not unplug a microphone or change48V here.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Do you want the rear microphone rather than the front instrument now?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII Hardware and Connections | Audient Documentation ↗Hardware and Connections — Front JFET instrument input overrides rear mic/line input1. Each microphone input has independent phantom power, enabled only after checking the microphone documentation. Four line outputs and dual headphone sockets have distinct routing; both headphone sockets share the same signal.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-2
Do you want the rear microphone rather than the front instrument now?
The front instrument will stop feeding channel1.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Disconnect only the front instrument cable
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII Hardware and Connections | Audient Documentation ↗Hardware and Connections — Front JFET instrument input overrides rear mic/line input1. Each microphone input has independent phantom power, enabled only after checking the microphone documentation. Four line outputs and dual headphone sockets have distinct routing; both headphone sockets share the same signal.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-3
Disconnect only the front instrument cable
Leave the rear microphone and its already verified phantom configuration undisturbed.
Look for: Perform only the stated operation, then confirm whether it could be completed.
- If Yes / check completed → Does the rear input1 now provide the intended signal?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII Hardware and Connections | Audient Documentation ↗Hardware and Connections — Front JFET instrument input overrides rear mic/line input1. Each microphone input has independent phantom power, enabled only after checking the microphone documentation. Four line outputs and dual headphone sockets have distinct routing; both headphone sockets share the same signal.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-4
Does the rear input1 now provide the intended signal?
Test through its meter; do not infer a preamp fault solely from the previous override.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Checks completed — report what happened
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII Hardware and Connections | Audient Documentation ↗Hardware and Connections — Front JFET instrument input overrides rear mic/line input1. Each microphone input has independent phantom power, enabled only after checking the microphone documentation. Four line outputs and dual headphone sockets have distinct routing; both headphone sockets share the same signal.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
Possible result
Checks completed — report what happened
Completion is not an automatic solved result. Report solved, partly helped, did not help or could not follow based on your actual observation. No Audio Review physical test is claimed.
steps completed
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Keep these observations for official support
A required prerequisite or response was not confirmed. Stop this sequence and use the exact model and partner documentation. Do not escalate to a factory reset, firmware installation, internal repair or unsafe wiring change.
next support
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
A required fact is unknown
Confirm the exact model, connection, partner capability and current control state before continuing. Do not guess settings or operate an updating product.
insufficient data
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.