Audio Fix / setup help
Audient iD14 MKII: avoid simultaneous iD Mixer and DAW input monitoring
Audient iD14 MKII: avoid simultaneous iD Mixer and DAW input monitoring. Check prerequisites and the actual response before reporting an outcome.
Manufacturer-documented Reviewed 2026-11-09 · Revision 1
Follow these checks in Audio Fix →When this guide applies
Input already audible through iD Mixer; software monitoring duplicates it.
Connection scope: USB audio. Symptom: Sound and picture are out of sync.
This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.
If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.
Checks and possible outcomes
Start at step-0. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.
step-0
Is the live input already audible through the intended iD Mixer monitoring path?
This flow relies on that known direct path; do not disable the only monitoring path.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Is the same input also software-monitored in the DAW?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII DAW Setup | Audient Documentation ↗DAW Setup — Logic selects iD14 input/output under Settings > Audio > Devices. Mixer-monitored inputs should not also be software monitored; DAW input/buffer configuration differs from monitor mix.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-1
Is the same input also software-monitored in the DAW?
An unrelated effect delay or playback problem is outside this doubled-monitor check.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → May the DAW input-monitoring path be disabled for that track?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII DAW Setup | Audient Documentation ↗DAW Setup — Logic selects iD14 input/output under Settings > Audio > Devices. Mixer-monitored inputs should not also be software monitored; DAW input/buffer configuration differs from monitor mix.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-2
May the DAW input-monitoring path be disabled for that track?
This changes monitoring, not recorded input gain or the take already recorded.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Disable software/input monitoring on that DAW track
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII DAW Setup | Audient Documentation ↗DAW Setup — Logic selects iD14 input/output under Settings > Audio > Devices. Mixer-monitored inputs should not also be software monitored; DAW input/buffer configuration differs from monitor mix.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-3
Disable software/input monitoring on that DAW track
Retain the known iD Mixer path. Do not mute the recording input or stop an unrelated session.
Look for: Perform only the stated operation, then confirm whether it could be completed.
- If Yes / check completed → Is the unwanted doubled or delayed second signal gone?
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII DAW Setup | Audient Documentation ↗DAW Setup — Logic selects iD14 input/output under Settings > Audio > Devices. Mixer-monitored inputs should not also be software monitored; DAW input/buffer configuration differs from monitor mix.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
step-4
Is the unwanted doubled or delayed second signal gone?
The observation does not claim a zero-latency software effect chain.
Look for: Confirm the actual prerequisite or observation. Unknown stops safely.
- If Yes / check completed → Checks completed — report what happened
- If No / cannot confirm → Keep these observations for official support
- If I do not know / cannot check → A required fact is unknown
- Manufacturer-documented iD14 MKII DAW Setup | Audient Documentation ↗DAW Setup — Logic selects iD14 input/output under Settings > Audio > Devices. Mixer-monitored inputs should not also be software monitored; DAW input/buffer configuration differs from monitor mix.Exact model named in the retrieved manufacturer document header. · Source checked 2026-11-09
Possible result
Checks completed — report what happened
Completion is not an automatic solved result. Report solved, partly helped, did not help or could not follow based on your actual observation. No Audio Review physical test is claimed.
steps completed
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Keep these observations for official support
A required prerequisite or response was not confirmed. Stop this sequence and use the exact model and partner documentation. Do not escalate to a factory reset, firmware installation, internal repair or unsafe wiring change.
next support
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
A required fact is unknown
Confirm the exact model, connection, partner capability and current control state before continuing. Do not guess settings or operate an updating product.
insufficient data
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.