Audio Fix / setup help

Dynaudio Focus 10: Compare the Focus inter-speaker link at 48 kHz

Compare the Focus inter-speaker link at 48 kHz. Follow the exact documented checks and retain the observation.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Dynaudio Focus 10. Only Focus Primary-to-Client internal wireless link, not an external TV WiSA transmitter or incoming network stream; preserve original 96 kHz state, accept interruption. Only normal external user controls; no reset, firmware installation, internal repair, mains alteration or earth lifting.

Connection scope: WiSA wireless audio. Symptom: Audio keeps cutting out.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

Is the intermittent loss confined to the Focus Primary-to-Client wireless link, with its WiSA status confirmed, current inter-speaker rate 96 kHz, no external WiSA transmitter, and permission for a temporary lower-rate comparison?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dynaudio Focus User Manual ↗Focus 10/30/50: Advanced Connections / WiSA, PDF p30 — The Focus WiSA screen displays Primary/Client link status and offers 48 or 96 kHz. The manual says 48 kHz can improve inter-speaker reliability depending on the local RF environment.Exact Focus 10 Primary/Client system; distinguish external WiSA transmitters from its own inter-speaker link. · Source checked 2026-11-09

a1

Open the Focus WiSA connection screen

In the selected system Settings > Advanced Settings > Connections open WiSA and confirm the Primary/Client link. Stop if it describes an external transmitter instead.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dynaudio Focus User Manual ↗Focus 10/30/50: Advanced Connections / WiSA, PDF p30 — The Focus WiSA screen displays Primary/Client link status and offers 48 or 96 kHz. The manual says 48 kHz can improve inter-speaker reliability depending on the local RF environment.Exact Focus 10 Primary/Client system; distinguish external WiSA transmitters from its own inter-speaker link. · Source checked 2026-11-09

a2

Select 48 kHz for that inter-speaker link

Select the offered 48 kHz option only for this documented inter-speaker link. Do not alter an external transmitter’s format or source settings.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dynaudio Focus User Manual ↗Focus 10/30/50: Advanced Connections / WiSA, PDF p30 — The Focus WiSA screen displays Primary/Client link status and offers 48 or 96 kHz. The manual says 48 kHz can improve inter-speaker reliability depending on the local RF environment.Exact Focus 10 Primary/Client system; distinguish external WiSA transmitters from its own inter-speaker link. · Source checked 2026-11-09

a3

Compare the same quiet passage

Compare the same content and retain the observation. Restore the original 96 kHz setting if the comparison is worse or unwanted.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Dynaudio Focus User Manual ↗Focus 10/30/50: Advanced Connections / WiSA, PDF p30 — The Focus WiSA screen displays Primary/Client link status and offers 48 or 96 kHz. The manual says 48 kHz can improve inter-speaker reliability depending on the local RF environment.Exact Focus 10 Primary/Client system; distinguish external WiSA transmitters from its own inter-speaker link. · Source checked 2026-11-09

result

Check the actual result

Is the Primary-to-Client connection more reliable in this comparison?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Dynaudio Focus User Manual ↗Focus 10/30/50: Advanced Connections / WiSA, PDF p30 — The Focus WiSA screen displays Primary/Client link status and offers 48 or 96 kHz. The manual says 48 kHz can improve inter-speaker reliability depending on the local RF environment.Exact Focus 10 Primary/Client system; distinguish external WiSA transmitters from its own inter-speaker link. · Source checked 2026-11-09

Possible result

Confirm the unknown detail before proceeding

Stop rather than infer an installed cartridge, partner, source level, cable capability, software version or control state.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, connection, control state and response. These checks do not diagnose a failed component or prescribe a reset, update, internal repair or mains change.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Keep the observed result

      This is the outcome observed in this setup, not a guaranteed cure, Audio Review physical test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top