Audio Fix / setup help
RME ADI-2 DAC FS: release a confirmed mute on the current headphone output
RME ADI-2 DAC FS — release a confirmed mute on the current headphone output. Use the stated exact hardware and connection scope.
Manufacturer-documented Reviewed 2026-11-09 · Revision 1
Follow these checks in Audio Fix →When this guide applies
Exact RME ADI-2 DAC FS. The current Phones/IEM output itself is positively muted, correct source and plug are already selected, and rear line outputs are unused. This does not use the Pro model or a guessed mute-toggle state.
Connection scope: USB audio · Optical digital audio. Symptom: There is no playback sound.
This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.
If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.
Checks and possible outcomes
Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.
scope
Confirm the model and connection
The current Phones/IEM output itself is positively muted, correct source and plug are already selected, and rear line outputs are unused. This does not use the Pro model or a guessed mute-toggle state.
Look for: Confirm this exact setup and observation before continuing.
- If Yes, I confirm → Pause source media
- If No / my setup differs → Continue with source and model support
- If I cannot confirm → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
a1
Pause source media
Pause media while leaving the intended output selected. Rear outputs must remain unused.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Lower volume while muted
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
a2
Lower volume while muted
Reduce the current headphone volume to a very low setting. On this model lowering volume retains mute; increasing volume would immediately unmute.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Set Mute OFF explicitly
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
a3
Set Mute OFF explicitly
Open I/O for the current Phones/IEM output, navigate Settings→Mute and set OFF only when ON was positively confirmed. Do not blindly toggle a remapped remote button.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Compare quietly
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
a4
Compare quietly
Resume familiar supported media cautiously at the new low level.
Look for: Observe the named indication or available control; stop if absent.
- If I completed this check → Check the result
- If I cannot complete this → Continue with source and model support
- If I cannot determine this → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
observe
Check the result
Is Mute OFF and quiet media now audible?
Look for: Confirm this exact setup and observation before continuing.
- If Yes, I confirm → Checks completed
- If No / my setup differs → Continue with source and model support
- If I cannot confirm → More information is required
- Manufacturer-documented RME ADI-2 DAC FS — official manual v34a ↗Sections5,10–12,14.1,19.4 and21.1 — ADI-2 DAC FS has local Source selection, per-output settings, volume/balance/mute, EQ, key lock, software-version readout, standby and USB buffer settings. Lowering volume retains mute, unlike many other DACs. I/O source Auto prioritises detected SPDIF. VOL encoder2press centres balance. No hardware reference-level or fixed-output increase is needed for these checks.Exact RME ADI-2 DAC FS. · Source checked 2026-11-09
Possible result
More information is required
An unknown state is not a diagnosis. Record the last visible indication and consult the exact model instructions.
insufficient data
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Continue with source and model support
Keep the source, connection and last observation. Do not reset, open equipment or change full-scale output to compensate for an unconfirmed result.
next support
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.
Possible result
Checks completed
The requested observation was confirmed in this setup. It does not establish a hardware repair or guarantee another source behaves the same.
steps completed
Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.