Audio Fix / setup help

Rega Planar 2: check the ordinary platter power control

Rega Planar 2 — check the ordinary platter power control. Follow the exact documented route and keep the actual result.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Rega Planar 2. Only an already-wired, correct supplied external power system. No outlet work, cable reconnection or internal diagnosis. Only normal external user controls; no mains modification, chassis opening, reset or firmware installation.

Connection scope: Device controls / power only. Symptom: Power-on or automatic standby isn’t working.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

Checks and possible outcomes

Start at scope. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

scope

Confirm the exact setup

The exact supplied power system is already correctly connected and dry/undamaged. The platter is assembled, the arm is secured, no record is playing, and you accept starting the motor.

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Rega Planar 2 official user manual ↗English pp.2–3 — Normal external on/off control — The turntable uses the on/off switch underneath the plinth. Use only the specified supplied Rega power adaptor.Exact Rega Planar 2 with RB220. Cartridge and power-supply variant must be confirmed; this is not a different Planar edition. · Source checked 2026-11-09

a1

Confirm the platter is currently stationary

Do not toggle a motor already running as an unexplained fault remedy.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Rega Planar 2 official user manual ↗English pp.2–3 — Normal external on/off control — The turntable uses the on/off switch underneath the plinth. Use only the specified supplied Rega power adaptor.Exact Rega Planar 2 with RB220. Cartridge and power-supply variant must be confirmed; this is not a different Planar edition. · Source checked 2026-11-09

a2

Use the normal under-plinth on/off switch

Switch the known off state on once. Do not touch rear calibration controls or disconnect power-supply interconnects.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Rega Planar 2 official user manual ↗English pp.2–3 — Normal external on/off control — The turntable uses the on/off switch underneath the plinth. Use only the specified supplied Rega power adaptor.Exact Rega Planar 2 with RB220. Cartridge and power-supply variant must be confirmed; this is not a different Planar edition. · Source checked 2026-11-09

a3

Observe platter rotation from clear of the arm

If it does not start, stop for dealer support. Do not open the motor or power supply.

Look for: Perform this one check and observe the actual response.

  • Manufacturer-documented Rega Planar 2 official user manual ↗English pp.2–3 — Normal external on/off control — The turntable uses the on/off switch underneath the plinth. Use only the specified supplied Rega power adaptor.Exact Rega Planar 2 with RB220. Cartridge and power-supply variant must be confirmed; this is not a different Planar edition. · Source checked 2026-11-09

result

Check the actual result

Does the correctly assembled platter rotate?

Look for: Choose only a detail you can confirm.

  • Manufacturer-documented Rega Planar 2 official user manual ↗English pp.2–3 — Normal external on/off control — The turntable uses the on/off switch underneath the plinth. Use only the specified supplied Rega power adaptor.Exact Rega Planar 2 with RB220. Cartridge and power-supply variant must be confirmed; this is not a different Planar edition. · Source checked 2026-11-09

Possible result

Confirm the unknown detail first

Do not infer a source setting, installed cartridge, connector role, software state or partner capability. Obtain the exact documentation before continuing.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Keep the actual observation for support

    Record the exact model, source, input and last observed response. These checks do not diagnose a failed component. No reset, service work or blind update is prescribed.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — keep the observed result

      This records the observation in this particular setup, not a guaranteed cure, physical Audio Review test or measurement.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top