Audio Fix / setup help

Jabra Elite 8 Active Gen 2: check Smart case pairing

Use the Gen 2 Smart case pairing button and blue indicator.

Manufacturer-documented Reviewed 2026-11-09 · Revision 1

Follow these checks in Audio Fix →

When this guide applies

Exact Jabra Elite 8 Active Gen 2 original earbuds and Smart case, with an Android or iOS phone/tablet. This is ordinary mobile pairing, not LE Audio setup, wired-case streaming or a factory reset.

Connection scope: Bluetooth. Symptom: My devices won’t pair or reconnect.

This is a documented check, not a diagnosis of your equipment. The model name does not confirm the selected input, mode, software or connected partner.

If your exact model or a required setting is unknown, use the “I don’t know” branch below. Do not apply a similarly named model’s instructions.

What owners have reported

These are public, self-reported experiences. They help explain the order of checks and the limits of a guide. They are not controlled tests, proof of a cause, a success rate or a substitute for the manufacturer instructions above.

User-reported Elite 8 Active Gen 2 repeats Bluetooth connection instructions

User-reported: an owner heard repeated pairing instructions despite a perceived connection and compared controls with an older Jabra model.

How this informs the checks: Use the documented Gen 2 case pairing method and verify the source connection independently of app setup.

Limits: The older model’s gestures and later reset/firmware suggestions are not proof of a Gen 2 remedy.

Read the original public discussion ↗ · Reviewed 2026-11-09

Checks and possible outcomes

Start at open. Follow the link that matches what you actually observe. Alternative branches are not a single sequence of actions.

open

Open the Smart case

Open its lid.

Look for: The lid stays open.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

inside

Put both earbuds inside

Place both original earbuds in the Smart case.

Look for: Both earbuds remain inside.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

mode

Use the case pairing button

Hold the Smart case button for three seconds.

Look for: The inner LED flashes blue.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

bluetooth

Enable phone Bluetooth

Turn on Bluetooth on your phone/tablet.

Look for: Bluetooth is enabled.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

select

Select the exact Gen 2 model

Choose Jabra Elite 8 Active Gen 2.

Look for: Check the connection state.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

remove

Remove the earbuds

Take both earbuds out of the Smart case.

Look for: Both are ready for use.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

observe

Does the source confirm a connection?

Report what its Bluetooth screen shows.

Look for: Choose only what you can confirm.

  • Manufacturer-documented Jabra Elite 8 Active Gen 2 manual ↗Rev D, section 6.1, page 17: Using the Smart case — Open the case with both earbuds inside; hold its button for three seconds until the inner LED flashes blue, then select Jabra Elite 8 Active Gen 2.OTE190L/R and CPB195 Gen 2 Smart case, not the CPB190 first-generation case. Phone/tablet procedure; no firmware minimum is stated. · Source checked 2026-11-09

Possible result

A required detail is unknown

Do not guess the model, connection state or indicator. Check the linked document for the exact product and source. If its control differs, use manufacturer support with the relevant app, firmware and OS details.

insufficient data

Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

    Possible result

    Continue with the manufacturer or source support

    These checks did not establish a working setup. No particular cause or failed component has been diagnosed. Do not repeat destructive resets or buy replacement hardware on the basis of this result.

    next support

    Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

      Possible result

      Checks completed — report what happened

      Completing the applicable checks is separate from solving the original problem. Use the feedback options to report solved, partial improvement, no improvement or difficulty following the steps.

      steps completed

      Reaching this result does not mean the issue is solved. Only your own feedback can report improvement.

        All Audio Fix guides → · TV & Audio Finder →

        Scroll to Top